China LED Lighting - Page 201

Features:

Base type: GU10

Input voltage: 85~260VAC with reversed polarity protect

Output power: 1w/3w/5w/7w/10w

Beam angle: 15/30/60/100degrees

Light source: 5w high power led

Body temperature: <45centigrade/66centigrade

Led working temp: <48centigrade/66centigrade

Temperature: -40~70 celsius degree

Brightness degradation: 3%-5%1kh

Life span: 50, 000 hours

Full range of color: Cool white, warm white, blue, green, red, yellow

Aluminium housing

No uv or ir radiation

Certifications: CE & ROHS

Applications:

Replacement for traditional halogen light bulbs, esp. Suitable for galleries, cosmetic counters, museum where UV or IR radiation is undesirable.

Specifications:

Voltage: 220V-240V AC, 50Hz/110-120V, 60Hz/DC/AC 12V

Output power: 1W

Beam angle: 15/30/60 degrees

LED working temperature: <48centigrade

Brightness degradation: 3%-5% 1kh

Base type: E27/E26/B22/MR16/GU10/JDR-E27/E14/E12

Features:

1. Use single 1W high power LED light source, with remarkable energy-saving effect.

2. Optional color: white, warm white, blue, red, yellow, green etc.

3. High energy-saving: saves 30-40% of electrical energy compared with incandescent lamp.

4. Long lifespan: above 50, 000hours.

5. Lower temperature: the light emitted would not produce much heat no matter how long it was used.

6. Healthy light: no radiation of any ultraviolet and infrared.

7. Environmental protection: no any chemicals like mercury and lead, easily recycled, electromagnetic disturbance.

Application:

Villa, restaurant, hotel, meeting room, show room, shop window, telephone cabinet etc.

1) Fully programmable: no cords, no wires, no software needed

2) LED: 21 x 7 Dot Matrix

3) Memory: up to 6 messages, up to 256 characters on each message

4) Messages automatically stored when switched off

5) Slim design

6) Dual magnetic closure backing

7) Programmed characters are as displayed

8) Note space is when there is no display character shown

9) 4 scrolling message speeds

10) Power ON/START and OFF/STOP

11) Cancel function

12) Power supply: CR2032 button battery

Our main products have six series:

1. All kinds of LED lamp (including various color, various shape, various luminous intensity and various viewing angle)

2. High power white LED for 1W, 3w, 5w, 10w, 20w, 30w and more high power led.

3. Infrared Emitting Diode, phototransistor and Infrared Remote Control Receiver.

4. Digital display and dot matrix

5. SMD LED, LED backlight

6. LED Application: Including sugar garden lighting, LED strip, LED microscope lighting etc.

For all above LED products We have the capability to open customize tooling in-house to meet your requirements.

Our solemn promises:

1. Competitive pricing

2. Short lead time (most products have 4 weeks average lead time)

3. Stringent quality control (ISO 9001, ISO 9000 & ISO 14001 certified), SGS

4. High volume capability

5. Responsive customer & technical support

6. Wide selections of LED

Safety: Low pressur of self power supplied system.

Portable: Novelty, small, light and easy to operate.

Energy Save: Charge by hand wind, without use public electronic.

Useful: Used in vehicle, tourism, camping, mine and other emergency situation.

Environmental Friendly: Without use dry batteries and refuse to pollution the environment; Use AC three phase dynamo and could anti-jamming from batteries.

Product Description

Working principle:

This item uses 3 phase generator without carbon brush for high power, which adopts switching voltage reduction circuit to produce 800mA output current to charge the built-in 300mAh/3. 6V Ni-Mh battery or come with a charging cable to recharge a mobile phone( while it does not recharge the inside battery). The green indicator is on when cranking the flashlight. The 2 position push switch is used to switch between 2 AAA batteries and the built-in battery via the voltage increase circuit to supply LED with power. The logic switch is used to control the working mode, i. E., two LED bulbs are turned on firstly and after, and the 0. 5W LED on and then off.

Product features

1> Crank by hand for power

2> Luminous flux>10lm, brightness>150000mcd

3> Big current to charge mobile phones

4> Waterproof

Cautions in use:

1. Fully insert the plug into the socket, otherwise it possibly leads to circuit shut off.

2. Crank it as even as possible (keep rotating steady). Too slowly cranking would make current weak and prolong charging time, and too violate cranking possibly damages the power transferring system. Keep cranking to charge a mobile phone continually, otherwise the power consumption will increase and affect the charging effect.

3. Pay attention to the holding gesture when cranking so as not to hurt your fingers.

4. In order to protect the battery's use life and the product's mechanical life, do not crank it for power continually more than 10 minutes.

5. Do not place this product where temperature or humidity is high.

6. This product may not fully charge the battery of a mobile phone.

7. Strictly use the cable our company specify to charge the specified mobile phones, otherwise it possibly damage mobile phones or a mobile phone's battery.

Crank it one time for not less than 1 minute per month so as to prolong the using life of the battery.

Trademark: SORBO

Model: SB-3065

Rope light(NL4)

Colors available: Clear, red, yellow, blue, green, orange, purple, pink, lime, lavender

Round solid tube with 2 wire and 30leds

Bulb spacing: 1.39cm/2.78cm/0.93cm

Weather-resistant PVC

GU10 AC 85V-260V

(1X1W LED)@350mA

OUTPUT POWER: 1W

NET WEIGHT: 41g

BODY TEMPERATURE: <40C

TOTAL LENGTH: 55mm

Type: L150

InputVoltage: 90-260VAC

LED power: 480P (180 pcs 300pcs are availble)

Typ. Lumen: 2000lm

Power: 24-30W

PS: Also we can produce as your requirements. And we have many other moudles, pls feel free to contact me for more details.

LASER CARD (TY225) is with two LED light and clock.